MASControl 1 Inch Pump Control

MASControl 1 Inch Pump Control

Options

1 Inch MASControl 22 PSI - $539.95
1 Inch MASControl 32 PSI - $539.95
1 Inch MASControl 42 PSI - $539.95

MASControl 1" pump control, 115/230V dual voltage provides demand-based pump control with run dry protection.
Our Price$496.95
List Price$570.00
SKUMASControl 1

Currently in stock



Product Description:
  • Maintains constant pressure and flow
  • Eliminates pump pressure switch
  • Built-in pressure and flow switch
  • Built-in check valve
  • Built-in dry-run protection
  • Assists in absorbing water hammer
  • Increases pump life
  • Dual voltage 115V / 230V A/C
  • Choose from 22, 32 or 42 PSI models
  • No adjustment or maintenance required
  • Simple installation saves space and time
  • Can be used with or without pressure tank
  • All stainless steel internal construction

Technical Specifications:

Single phase power-supply voltage

115V / 230V A/C

Voltage variation tolerance

± 10%

Frequency

50 / 60 Hz

Full load amp rating

115V A/C 16 FLA

Full load amp rating 230V A/C 20 FLA
Electronic box NEMA 12 enclosure
Threaded conduit connections .5'' NPT
Max working pressure 145 PSI
Max working temperature 149 °F

NEMA 12
The electronic board is completely dust-proof.

MAXIMUM OPERATING TEMPERATURE 149 °F
The device is built to work in an environment in which the temperature may reach 149 °F.

DEVICE COMPONENTS:

MASControl components

 

Three Different Factory Preset Cut-In Pressures
PSI of Model 22 PSI 32 PSI 42 PSI
Pump Minimum PSI 45 PSI 55 PSI 70 PSI
Max Elevation from Controller to Tap 50 Feet 70 Feet 90 Feet


Construction Details:

Body, non-return valve, rear part and knob are molded in 30% fibreglass reinforced polyamide 6 (PA6GF30).
This allows for obtaining a high resistance to wear and pressure.

The diaphragm is molded in EPDM ( Ethylene Propylene Diene Monomer ).
This guarantees exceptional reliability and durability.

The flow valve is in stainless steel (AISI 304).
The dimensional stability of the metal guarantees the operation of the components .

The spring is made in UNI 3823 steel wire.
The stabilization process guarantees the operation of the pressure switch, essential for the pump start-up precision and the system pressure adjustment. The dimensions and structure of the same allow for considerably reducing the effects of water hammering.

The box containing the electrical part is molded in shockproof self-extinguishing PBT.

The use of prime materials and top-of-the-range components allows for achieving high levels of dimensional stability, resistance to wear and bursting, and duration over time.


Installation:

The device can be mounted either directly onto the pump or between the pump and the first service.

If the input pressure of the device exceeds 145 PSI, install a pressure reducer between the pump and the device itself.

No tap can be mounted between the pump and the device.

It is essential to mount the device with the flow arrows pointing upwards (fig. A).
mascontroller It is recommended to connect the output of the device to the system by means of a ball valve and flexible tube (fig. B).

Before starting the device check that the pump is correctly primed.


Electrical Connections:

Installation Wiring Diagram - 115V A/C 2-Wire Pumps
For 115V A/C motors exceeding 16 full load amps, use magnetic starter to avoid damage to MASCONTROL. See separate magnetic starter wiring diagram.


 

Installation Wiring Diagram - 230V A/C Single Phase 2-Wire Pumps
For 230V A/C motors exceeding 20 full load amps, use magnetic starter to avoid damage to MASCONTROL. See separate magnetic starter wiring diagram.

Pressure Loss Chart
Flow rate GPM 5 10 15 18 20 25 30 35 40
MCA ( 1” ) Pressure Loss (PSI) 0.5 1.5 4 6.5 8.5
MCB ( 1.25” ) Pressure Loss (PSI) 0.5 1.5 2.5 3.5 5.5 7.5 10 12.5
Pressure Loss Chart with a Bypass Application
Flow rate GPM 20 30 40 50 60 70 80
MCA x 1'' Pressure Loss (PSI) 3 5 9 14 19 / /
MCB x 1.25'' Pressure Loss (PSI) 2 2 3 5 8 10 12
MCB x 1.5'' Pressure Loss (PSI) 2 2 3 4 6 7 8

 

Use MASCONTROL in bypass when friction loss is excessive.
The main bypass piping must not exceed 1.5”, while the system pipe could be bigger.

For minimal delivery demands, the application of a small expansion tank downstream from the MASCONTROL allows for reducing the pump start-ups.
(Example: a glass of water, ice-making machine, inverse osmosis systems, or old systems with small losses).

It is recommended to preload the expansion tank at a slightly lower value than the restart pressure calibration value of the device.
(Example: MASCONTROL calibrated at 42 PSI, tank preloaded at approximately 40 PSI).



:

Product Documents:


Related products you may find useful:

 
RainFlo MHP75 3/4 HP Pump
View RainFlo MHP75 Multistage Horizontal 3/4 horsepower pump with durable and quiet performance up to 26 GPM and 65 PSI (maximum).

click to see more

 
 
RainFlo PC115 115V Automatic Pump Controller
View Electronic pump controller with integral flow regulation provides industry-leading demand-based pump control with built in dry-run protection and pressure gauge.

click to see more

 
 
RainFlo 1 Inch Water Meter

The RainFlo 1" water meter provides a simple, effective solution to monitor the amount of rainwater you have used from your rainwater harvesting system.

Our Price: $104.95
List Price: $174.95

click to see more

 

The RainFlo 1" water meter provides a simple, effective solution to monitor the amount of rainwater you have used from your rainwater harvesting system.

Our Price: $104.95
List Price: $174.95

click to see more

Related products you may find useful:

 
RainFlo MHP75 3/4 HP Pump
View RainFlo MHP75 Multistage Horizontal 3/4 horsepower pump with durable and quiet performance up to 26 GPM and 65 PSI (maximum).

click to see more

 
 
RainFlo PC115 115V Automatic Pump Controller
View Electronic pump controller with integral flow regulation provides industry-leading demand-based pump control with built in dry-run protection and pressure gauge.

click to see more

 
 
RainFlo 1 Inch Water Meter

The RainFlo 1" water meter provides a simple, effective solution to monitor the amount of rainwater you have used from your rainwater harvesting system.

Our Price: $104.95
List Price: $174.95

click to see more

 

The RainFlo 1" water meter provides a simple, effective solution to monitor the amount of rainwater you have used from your rainwater harvesting system.

Our Price: $104.95
List Price: $174.95

click to see more